7 min read

Mid-Project EOR Design Revisions and WPS Requalification

When the engineer of record revises joint details, base metals, or thicknesses mid-project, your existing WPS may no longer cover the work. Here's how to assess the impact and respond.

New to procedures? Start with WPS welding: what a welding procedure specification is, with a filled-in example.

Design changes are a reality on steel construction projects. The engineer of record (EOR) issues a revised connection detail mid-fabrication because a load path was revised, an architect changed an exposed connection condition, or a RFI response altered the original joint configuration. For the structural steel fabricator and their QC program, the question becomes immediate: does the existing WPS program still cover the work?

The answer depends on exactly what changed, and the analysis must be done systematically against AWS D1.1 qualification requirements — not on a gut-feel basis or via informal EOR approval.

The Four Categories of Change That Matter

Not every design revision affects WPS coverage. The essential variables in AWS D1.1:2025 Table 6.6 define what changes require a new PQR or a re-qualified WPS. The changes most commonly introduced by mid-project design revisions fall into four categories:

1. Joint Type Change

A change in joint type — from a simple fillet weld to a CJP groove weld, from a PJP groove weld to a CJP, or from a groove weld to a plug/slot weld — requires a different WPS. Each joint category has distinct qualification requirements, and coverage does not transfer between them. If the EOR revises a shear tab from a fillet weld to a CJP groove weld for a moment-frame upgrade, the fillet weld WPS provides no qualification basis for the CJP joint.

2. Base Metal Change

A change in base metal specification or grade is an essential variable. Table 6.6 addresses this in terms of base metal groups (defined by Table 5.6 for prequalified materials, or by test qualification for non-prequalified materials). For prequalified WPS applications, the question is whether the new material is in the same group as the original, or in a group covered by the existing WPS. For test-qualified WPS applications, review whether the new material was included in the PQR scope, either directly or by group coverage.

Common mid-project scenarios:

  • EOR upgrades from A36 plate to A572 Grade 50 or A572 Grade 65 to reduce member size. A572 Grade 50 is Group II in Table 5.6; A36 is Group I. If the existing WPS only covered Group I, the upgrade to Grade 50 requires a WPS that covers Group II.
  • EOR substitutes A500 Grade B HSS with A500 Grade C due to availability. These are both A500 and are covered under the same Table 5.6 entry — no WPS change is typically needed if other variables remain constant.
  • EOR specifies A913 Grade 65 for a heavy column instead of A992 Grade 65. A913 Grade 65 and A992 are both listed in Table 5.6, but their group assignments and WPS compatibility should be confirmed in the specific edition in use.

3. Joint Geometry Changes Beyond Qualified Limits

For test-qualified WPS procedures, the PQR establishes ranges for certain joint geometry parameters. If the EOR revises a groove angle from 45° to 25°, or increases root face thickness from 1/8 inch to 3/8 inch, the question is whether the revised geometry falls within the qualified range or requires a new PQR.

For prequalified WPS procedures, the revised joint geometry must fall within the dimensional limits shown for the applicable joint designation in Clause 5 Figures 5.1 (CJP), 5.2 (PJP), or 5.3 (fillet). If the revised detail falls outside those limits — whether from a groove angle change, root opening adjustment, or added weld access hole that affects the joint configuration — the joint is no longer prequalified and a PQR is required.

4. Base Metal Thickness Change

Both the minimum and maximum thickness of the base metal are essential variables in certain contexts. For prequalified WPS applications, there is no explicit thickness limit based on PQR coupon thickness (the prequalified WPS covers any thickness if the joint fits within Clause 5 limits and Table 5.11 preheat requirements are met). For test-qualified WPS applications, the qualified thickness range is derived from the PQR coupon thickness per the rules in Clause 6.

If the EOR revises connection details to use significantly thicker plate (say, changing from 1-inch gussets to 2.5-inch gussets), confirm that the existing PQR's qualified thickness range covers the new dimension. When the connection requires joining plates of different thickness, the controlling thickness for WPS coverage is typically the thinner piece.

Preheat Implications of Base Metal Changes

Even when a base metal change does not require a new WPS or PQR, it may change the preheat requirement. AWS D1.1:2025 Table 5.11 defines minimum preheat by base metal type and thickness. A switch from A36 to A572 Grade 50 or A572 Grade 65 at the same thickness may increase the minimum preheat requirement because higher-strength steels generally require higher preheat to control hydrogen-related cracking risk.

Before the first production weld on the revised base metal, verify the Table 5.11 preheat requirement for the new material and confirm it is reflected in the WPS or its supporting documentation. If the revised WPS preheat is higher than the original, update the procedure documentation and train the welders on the new minimum.

Structural Implications of Joint Type Changes

Design revisions often change joint type for a structural reason — a connection is upgraded from simple shear to moment-resisting, or a tension chord connection is upgraded from fillet to CJP to eliminate the PJP effective throat limitation. These are not minor administrative adjustments; they change the structural demand on the weld and therefore require a weld procedure that is fully qualified for the revised joint category.

An EOR cannot retroactively accept an improperly qualified weld because the connection still "passes" structurally. AWS D1.1 qualification requirements are independent of structural design adequacy — a weld deposited without a valid covering WPS is a code non-conformance regardless of whether it meets strength requirements. If a CWI discovers that production welds were made under a WPS that did not cover the revised joint type, the disposition must address both the structural adequacy (EOR's domain) and the qualification non-conformance (QC's domain).

The CWI's Role at Design Revision Receipt

When a design revision is received — whether as an RFI response, an ASI (architect's supplemental instruction), or a formal drawing revision — the QC manager or CWI should immediately assess the WPS impact before those joints enter fabrication. This is a gate-keeping function: once the revised joint is welded without a valid WPS, the corrective action cost is significantly higher than the cost of identifying the gap beforehand.

The review should answer three questions:

  1. Does the revised joint type, base metal, or geometry fall outside the existing WPS program coverage?
  2. If a gap exists, can it be resolved with a new prequalified WPS (no PQR needed), or is a PQR required?
  3. What is the lead time to have a valid WPS in place, and does the fabrication schedule need to hold on those specific joints?

A written assessment, even a brief one, documents that the review was done and protects the shop in the event of a later inspection finding. Some shops formalize this as a "WPS coverage check" step in their change management procedure — a reasonable practice for projects with frequent design revisions.

When the EOR Letter Is Not Enough

Fabricators occasionally receive an EOR letter or email stating that an existing WPS "should be acceptable" for the revised joint, without the EOR specifically reviewing the qualification basis. While EOR approval is required for submittals and for disposition of weld non-conformances, it does not substitute for a valid WPS. The EOR's role is design and acceptance; AWS D1.1 qualification is the fabricator's responsibility.

If the EOR's project engineer is not familiar with AWS D1.1 qualification requirements (common outside firms that specialize in steel construction), the QC manager may need to briefly explain the distinction: the EOR can accept or reject the design outcome, but the qualification basis for executing the weld is the fabricator's obligation under the code. This is not an adversarial position — it protects both parties by ensuring that the weld procedure documentation accurately reflects what was done.

Practical Documentation Steps

When a design revision requires a new or revised WPS:

  1. Identify all joints affected by the design change, not just the ones that triggered the original review. A single RFI response may affect dozens of connections with similar details.
  2. Determine the qualifying basis for the revised joint — prequalified per Clause 5, or qualified by test with an existing PQR that covers the new parameters.
  3. Issue a hold on production welding of affected joints until the new WPS is available and reviewed.
  4. Update the WPS program documentation to reflect the new procedure, and confirm that the Annex J Form J-1 entries accurately reflect the revised conditions.
  5. Brief welders on any parameter changes — particularly preheat changes, which are the most common practical effect of base metal upgrades.

For shops that work on projects with frequent design revisions, maintaining a broader WPS qualification program — one that covers multiple base metal groups, a range of thicknesses, and both backed and open-root conditions — reduces the frequency of production holds when changes arrive. The investment in a comprehensive PQR library at project start pays back every time a mid-project revision comes through without triggering a new qualification cycle.

For related guidance, see WPS requalification triggers checklist under AWS D1.1 and prequalified vs. qualified-by-test WPS cost comparison. Our pricing page covers how the WPS editor and PQR tracker help shops manage procedure scope against active project specifications.


Rule library based on AWS D1.1:2025; verify against your governing edition — the AHJ or contract may specify 2020 or earlier.

FAQ

Frequently asked.

If the EOR revises a joint from a T-joint fillet to a CJP groove weld, does the existing WPS cover it?
No. A fillet weld WPS does not cover CJP groove welds. These are different joint categories with different qualification requirements. A new WPS — either prequalified or backed by a PQR — is required for the CJP joint.
The EOR changed the base metal from A36 to A572 Grade 50. Do I need a new PQR?
It depends on the basis of your existing WPS. If the WPS is prequalified and covers A572 Grade 50 (a Group II metal in Table 5.6), and all other variables remain within prequalified limits, no new PQR is needed. If the WPS was qualified by test for A36 specifically, review Table 6.6 to confirm whether A572 Grade 50 falls within the qualified base metal group range.
Can the EOR approve the use of an existing WPS that doesn't technically cover the revised joint?
No. The EOR can review and accept submittals, but they cannot waive AWS D1.1 qualification requirements. Only a properly qualified and documented WPS covers production welding. A letter of EOR acceptance is not a substitute for a valid WPS based on the applicable prequalified provision or a completed PQR.
How should a CWI document a WPS coverage gap found after design revisions?
Issue a written notification to the QC manager and project manager identifying the specific joint(s) where the existing WPS no longer applies. Do not allow production welding to proceed on those joints until a valid WPS is in place. Document the hold and the basis for it in the inspection record.

More from the blog