Web Penetration Reinforcement Ring Welds: AWS D1.1 WPS Guide
WPS requirements for reinforcement ring welds at MEP beam penetrations: prequalified fillet qualification, preheat from Table 5.11, and CWI inspection under AWS D1.1:2025.
Structural beams in fab shops and in the field regularly need circular or rectangular penetrations for mechanical, electrical, and plumbing systems. When a structural engineer approves a web opening and specifies a reinforcement ring or plate, that ring gets welded to the beam web and flanges under AWS D1.1 requirements. Knowing which WPS applies—and what the CWI must verify before, during, and after welding—keeps the job moving and the audit packet clean.
Why Web Openings Require a WPS
A penetration ring is structural weld territory the moment a fillet weld joins it to a primary member. AWS D1.1:2025 applies to all structural steel welds on members carrying design loads, regardless of whether the weld is a small circumferential fillet or a full-height stiffener CJP. The absence of a WPS—or the wrong WPS—is an immediate nonconformance on any AISC-certified project or inspector-witnessed job.
The opening itself must be approved by the Engineer of Record before any cutting begins. AISC Design Guide 2 (Steel and Composite Beams with Web Openings) is the standard reference for unreinforced and reinforced circular or rectangular openings. AWS D1.1 picks up after the EOR approves the opening and specifies the reinforcement detail.
Prequalified WPS Applicability
Most web penetration reinforcement welds qualify for a prequalified WPS under AWS D1.1:2025 Clause 5, provided:
The base metal is a Table 5.6 prequalified steel (A36, A572 Gr 50, A992, A500 Grade B/C, and others)
The filler metal is a Clause 5 prequalified classification (E7018, E71T-1, ER70S-6, and their low-hydrogen equivalents)
The joint is a standard fillet weld with no groove or partial joint penetration requirement
The process is SMAW, FCAW-G, GMAW, or SAW in a prequalified parameter set
No PQR test is required when these conditions are met. If the EOR specifies a full-penetration weld between the ring and the web—uncommon but occasionally required at high-fatigue connections—then a Clause 5 prequalified CJP joint geometry must be achievable or a Clause 6 tested WPS is needed.
AWS D1.1:2025 Table 7.7 governs minimum fillet weld size based on the thinner part joined. The table key is the thinner part of the two members:
Thinner Part Thickness
Minimum Fillet Size (Low-Hydrogen)
≤ 1/4 in [6 mm]
1/8 in [3 mm]
> 1/4 to 1/2 in [6–12 mm]
3/16 in [5 mm]
> 1/2 to 3/4 in [12–19 mm]
1/4 in [6 mm]
> 3/4 in [19 mm]
5/16 in [8 mm]
Rule library based on AWS D1.1:2025; verify against your governing edition.
For a typical W-shape web ranging from 1/4 to 3/8 inch, the minimum fillet is 3/16 inch when using SMAW E7018 or FCAW-G. The reinforcement ring plate thickness also matters—if the ring is thicker than the web (a common detail), the web thickness controls the minimum fillet size.
The design-required weld size typically exceeds the Table 7.7 minimum; always use the larger of the design size and the code minimum. See minimum fillet weld size under AWS D1.1 Table 7.7 for the full table and application notes.
Essential Variables Under Table 6.6
AWS D1.1:2025 Table 6.6 lists the essential variables that, if changed, require a new WPS or requalification. For reinforcement ring welds, the variables most likely to trigger a WPS update:
Base metal specification change. An A36 web welded to an A572 Grade 65 ring plate is a base metal group change. Verify the WPS covers the actual steel specification on the CMTR before the first arc.
Filler metal classification change. Switching from E7018 to E71T-1M (FCAW-G) is a process and filler change requiring a separate WPS. Per Table 6.6 Row 4, the A5.36 classification is no longer permitted for GMAW and FCAW-G in the 2025 edition—a detail that catches shops upgrading their WPS libraries from 2020 documents.
Electrode-to-supplemental filler ratio (FCAW-G). AWS D1.1:2025 Table 6.6 Row 7 requires the ratio of supplemental filler to electrode wire to remain within ±10% of the qualified value. This is a 2025 change from the 2020 edition.
Position change. A WPS qualified in 1F and 2F does not cover 3F or 4F. Web penetrations on horizontal beams in the shop are typically 2F (horizontal fillet) or 1F (flat), but field-installed rings on diagonal braces or columns may require additional position qualification.
For prequalified fillet welds, preheat is taken from AWS D1.1:2025 Table 5.11 based on base metal type and thickness. For the most common case—A36 or A572 Gr 50 web up to 3/4 inch (19 mm) thick with a low-hydrogen process—the minimum preheat is 32°F [0°C]. At greater thicknesses or with higher-carbon equivalents, preheat rises to 150°F [65°C] or more.
Interpass temperature must not exceed the WPS maximum (typically 500°F [260°C] for carbon and low-alloy steels unless otherwise specified). On thin webs, controlling heat input matters: excessive interpass temperature in thin-web sections accelerates distortion and can cause burn-through on webs lighter than 3/16 inch.
Before striking an arc on a penetration ring, the inspector should verify:
EOR approval documented — drawing revision, RFI response, or engineering memo on file.
Penetration size and location verified — measured from beam end, centerline, and nearest connection.
Cut quality accepted — flame-cut or plasma-cut edges on the web and ring meet surface finish requirements per AWS D1.1:2025 Clause 5.
Ring plate and web CMTRs on file — heat numbers matched to the material.
WPS on the work package — correct process, filler metal, and position listed; preheat value stated.
Preheat verified — measured 3 inches [75 mm] from the joint on both the ring and the web face.
Fit-up acceptable — fillet weld root opening at or below 1/16 inch [2 mm] without correction; up to 3/16 inch [5 mm] requires the leg increased by the gap amount.
In-Process and Post-Weld Checks
During welding: Verify the welder holds the qualified position. Record or spot-check amperage, voltage, and travel speed if the WPS lists ranges. Check interpass temperature before each pass on restrained joints.
After welding:
Fillet size — Use a bridge cam or fillet gauge, measuring on each face of the ring. All passes must meet the design-specified size.
Visual acceptance criteria — AWS D1.1:2025 applies: no cracks, no incomplete fusion at the weld root on the accessible side, no undercut exceeding 1/32 inch [1 mm] adjacent to a tension zone.
Profile — Circumferential fillet welds on rings can develop convex profiles. Excessive convexity that reduces the effective throat may need grinding.
Distortion — Web out-of-plane bowing adjacent to the ring is common on thin webs. Document and report to the EOR if camber or sweep is affected.
MT or PT surface testing is required only if specified in the project documents or if visual inspection reveals a suspect indication.
Common WPS Mistakes on Ring Weld Jobs
Using the wrong WPS for the base metal. A WPS written for A36 welded with E7018 applies to A572 Gr 50 (same prequalified base metal group per Table 5.6), but does NOT cover A913 Grade 65 without a separate WPS.
Missing position qualification in the field. A shop-qualified welder holding only 1F and 2F cannot perform a 3F or 4F ring weld without additional WPQ testing.
Undersized fillet at restarts. Circumferential welds stop and restart, and restarts commonly produce undersize craters. Inspect continuously around the ring, not just at the top and bottom.
No preheat in cold weather. Even A36 at under 1/2 inch thickness with a low-hydrogen process has a 32°F [0°C] floor. Cold morning starts without temperature checks are a frequent audit finding.
Web penetration reinforcement ring welds fall under AWS D1.1:2025 when attached to structural members. Most qualify for a prequalified WPS under Clause 5 as standard fillet welds. Minimum fillet weld size comes from Table 7.7—use the thinner part for the lookup. Preheat from Table 5.11 based on base metal type and thickness. CWIs must verify EOR approval, fit-up, preheat, and post-weld visual acceptance before signing off. Document everything—reinforcement ring welds show up in AISC audit packets and IBC special inspection reports.
FAQ
Frequently asked.
Does a web penetration reinforcement ring weld need a full PQR, or can it use a prequalified WPS?
If the reinforcement weld is a fillet weld meeting all Clause 5 prequalified joint and process criteria, a prequalified WPS is sufficient—no PQR test is required. Most shop-cut circular hole reinforcement rings qualify as standard fillet joints.
What is the minimum fillet weld size for welding a 3/8-inch reinforcement ring to a W-shape web?
Per AWS D1.1:2025 Table 7.7, minimum fillet weld size is based on the thinner part joined. For a 3/8-inch (10 mm) web or ring plate, the minimum is 3/16 inch [5 mm] for low-hydrogen processes (SMAW E7018, FCAW-G). Always verify which part is thinner—it may be the web.
Does AWS D1.1 address position qualification for circular fillet welds around penetration rings?
AWS D1.1 position qualifications apply to weld type and groove or fillet category, not joint geometry. A fillet weld qualifier in 1F, 2F, 3F, and 4F covers circular ring welds in the same spatial orientations. The welder must hold the applicable position qualification.
Who approves the structural opening location and size before welding begins?
The Engineer of Record must approve penetration size, location, and reinforcement design per the applicable design code (AISC Design Guide 2 or project-specific drawings). AWS D1.1 governs only the welding—the opening approval is an engineering judgment the CWI cannot substitute.