Cable Tray and Conduit Rack Supports: WPS Requirements Under AWS D1.1
CWI and QC guide to welding procedure specifications for structural cable tray and conduit rack supports—base metal, fillet size, process qualification, and inspection under AWS D1.1:2025.
Structural cable tray and conduit rack supports rarely draw the same scrutiny as a moment frame or transfer girder—but in an AISC-certified fab shop or on a project with IBC special inspection, these weldments are subject to the same AWS D1.1 procedural requirements as any other structural member. Getting the WPS right for support steel is a common gap, and it shows up during AISC fabricator certification audits as an NCR when the shop cannot produce a qualifying document for the lighter support framing.
Why Support Steel Falls Under AWS D1.1
Cable tray racks, conduit unistrut frames, and pipe hanger steel are rarely called out by name in a welding procedure library. But when the host project specifies AWS D1.1 as the governing code—which is essentially all AISC-certified fabrication and most IBC Chapter 17 special inspection work—the code applies to all structural steel weldments unless the EOR explicitly excludes them.
AWS D1.1:2025 Clause 1.3 defines its scope: the code covers welded joints in structural steel used for buildings, bridges, and other structures. The practical threshold is load-carrying intent. A bolted unistrut system carrying lightweight conduit only may not trigger D1.1; a welded A36 angle-and-channel support frame carrying a loaded cable tray or multiple heavy conduit runs at elevation is load-carrying structural steel.
When in doubt, treat it as structural. The cost of a D1.1-compliant WPS is trivial. The cost of an audit finding—or a support failure—is not.
Base Metal Selection for Support Frames
The two most common base metals in conduit and cable tray support framing are:
ASTM A36 — the standard low-carbon structural steel for angles, plates, channels, and small wide flanges. A36 is listed in AWS D1.1:2025 Table 5.6 as a prequalified base metal, Group I, so it qualifies automatically for a Clause 5 prequalified WPS without a PQR test.
ASTM A500 Grade B/C — the standard for cold-formed round and rectangular HSS tube used in support posts and frames. A500 Grade B (rectangular, Fy = 46 ksi) and Grade C (round, Fy = 46 ksi) are also listed in Table 5.6 as prequalified base metals.
ASTM A53 Grade B pipe — used for round posts and sleeves. A53 Grade B is included in Table 5.6, Group I.
For supports using these three base metals in any combination, a Clause 5 prequalified WPS is available, which means no PQR test is required provided all other prequalification conditions (joint geometry, filler metal classification, preheat) are met.
Minimum Fillet Weld Size and Table 7.7
The most common weld type on support steel is a fillet weld: angle to base plate, channel to column, HSS post to bearing plate, or frame members welded at corner joints. AWS D1.1:2025 Table 7.7 sets minimum fillet weld size based on the thickness of the thinner part connected, using low-hydrogen process criteria:
Thinner Part Thickness (T)
Minimum Fillet Size
T ≤ 1/4 in [6 mm]
1/8 in [3 mm]
1/4 in < T ≤ 1/2 in [12 mm]
3/16 in [5 mm]
1/2 in < T ≤ 3/4 in [19 mm]
1/4 in [6 mm]
T > 3/4 in [19 mm]
5/16 in [8 mm]
For typical 3/16-inch angle framing, the minimum is 1/8 inch. For 3/8-inch channel or tube wall, the minimum is 3/16 inch. The engineer's drawings may specify a larger weld—use whichever is greater.
One important practical point: the minimum fillet size in Table 7.7 applies per pass for a single-pass weld and to the finished weld size for a multi-pass sequence. If the first pass is undersized on a single-pass fillet, that is a code violation even if the finished weld nominally meets size.
Rule library based on AWS D1.1:2025; verify against your governing edition.
Filler Metal and WPS Classification
For A36 and A500 base metal, the standard filler metals used in structural fab shops cover the range:
SMAW: AWS A5.1 E7018 (H8 suffix or better for low-hydrogen compliance). E7018 is the workhorse for support steel in all positions.
FCAW-G: AWS A5.20 E71T-1 or E71T-9. These are the most common production fillers for support frames in shops with wire feeders.
GMAW: AWS A5.18 ER70S-6 is acceptable for thin-gauge support framing and miscellaneous attachments.
The WPS must state the specific electrode classification and AWS specification number. "E7018" alone is not sufficient—"AWS A5.1 E7018-H8" is the correct designation for a low-hydrogen electrode with the hydrogen designator.
For prequalified WPS under Clause 5, the filler metal must appear on the Table 5.4 prequalified filler metal list (by process and base metal strength group). All three fillers listed above are prequalified for Group I base metals.
Preheat Requirements
For support framing in A36 and A500, preheat requirements are typically low or zero when the material is thin and ambient conditions are acceptable. Per AWS D1.1:2025 Table 5.11:
A36 and A500 in the Group I / 50 ksi and under category: 32°F [0°C] minimum when T ≤ 3/4 inch, with no preheat required above ambient provided the steel is above 32°F.
However, if heavier sections are used—for example, a 1-inch base plate for a large cable tray anchor—preheat requirements increase. The CWI must reference Table 5.11 input variables (heat category based on weld heat input and member thickness) rather than relying on the "it's just angle iron, no preheat needed" assumption.
Document the minimum and maximum interpass temperature on the WPS even for thin-section support steel. This prevents shop-floor ad hoc decisions that deviate from the qualified range.
Position Qualification
Support steel often requires welding in multiple positions: flat (1F/1G) for shop-fabricated frames on a welding table, horizontal (2F) for field attachments to columns, and overhead (4F) for field fillet welds under cable trays at elevation.
A prequalified WPS may cover any position for the listed process provided the weld joint geometry and pass sequence meet Clause 5 requirements. For example, SMAW E7018 with a prequalified T-joint geometry is prequalified in all positions (1F, 2F, 3F, 4F) per Clause 5.
A tested WPS qualified under Clause 6 extends position coverage per Table 6.6 essential variable rules: a groove weld test plate in position 2G qualifies 2G and 1G only; additional positions require additional test plates or a 3G/4G qualification plate. For fillet welds, position qualification follows the WPQ rules—a welder qualified in 3F (vertical fillet) also qualifies 1F and 2F.
Confirm position coverage before assigning a welder to field overhead work. Overhead (4F) fillet qualification is not automatic from a 3F plate.
CWI Inspection Focus for Support Steel
Visual inspection is the primary NDE method for support fillet welds. Per AWS D1.1:2025, all structural welds receive visual inspection. The CWI holds the following for support steel:
Pre-weld: Verify fit-up gap (maximum 3/16 inch for fillet welds without WPS allowance), base metal identification matches WPS, filler metal classification correct, preheat verified if required, and welder WPQ current.
In-process: Confirm pass sequence, interpass temperature within range, electrode storage compliant (E7018 from sealed container or heated oven, not left open on the floor), and weld bead profile acceptable.
Post-weld visual: Check fillet weld size with a weld gauge (the most common deficiency on support steel is undersized fillets at start and stop craters), look for porosity, undercut, overlap, cracks, and arc strikes outside the weld zone.
For fillet welds on support steel, NDE beyond visual is typically not required unless the owner specification or project special inspection schedule calls for it. If MT or PT spot checks are specified, the inspection frequency and acceptance criteria will be in the contract documents.
WPS Document Checklist for Support Steel
A complete WPS package for cable tray and conduit rack supports should include:
WPS form — Annex J Form J-1 format recommended. Must list joint type (fillet), base metal specification and thickness range, filler metal classification and AWS specification, process, position(s), preheat/interpass temperature range, amperage/voltage/travel speed ranges, and WPS number with revision date.
Basis of qualification — Either "Prequalified per AWS D1.1:2025 Clause 5" with supporting clause references, or reference to a qualifying PQR number if tested.
Supporting PQR — Only required for Clause 6 tested WPS. For prequalified WPS, the clause reference serves as the basis.
Authorized signature — The WPS must be signed/approved by a responsible welding engineer, CWI, or authorized representative. Per D1.1:2025, the fabricator is responsible for WPS development; a CWI signature on the form is good practice even if not mandated by name.
For shops seeking or maintaining AISC certification, support steel WPS documentation is part of the QC manual audit. Auditors look for coverage of all weld types in production scope—if conduit rack frames are in your fabrication scope and there's no WPS covering that work, it's a finding.
If you're building out a prequalified WPS library for your shop's miscellaneous steel scope, our prequalified WPS Clause 5 overview covers the base conditions that allow you to skip PQR testing.
Does AWS D1.1 apply to cable tray and conduit rack supports?
Yes, when the support framing is fabricated from structural steel (angle, channel, wide flange, HSS tube) and welded, AWS D1.1 applies. The governing contract documents—typically an AISC-certified fabricator's scope or the project IBC special inspection schedule—will confirm whether D1.1 is called out. Many EPC and industrial contractors specify D1.1 for all structural weldments in a facility, including support steel.
What fillet weld size is typically required for conduit rack frame welds?
Minimum fillet weld size is set by AWS D1.1:2025 Table 7.7 based on the thickness of the thinner part joined (T for low-hydrogen processes). For 3/16-inch angle or channel framing, the Table 7.7 minimum is 1/8 inch. For 1/4-inch to 1/2-inch members, the minimum is 3/16 inch. These are code minimums; the structural engineer's drawings govern if they specify a larger size.
Can a prequalified WPS cover cable tray support welds?
Yes. Fillet welds on A36 or A500 Grade B material using SMAW E7018 or FCAW-G E71T-1 with AWS D1.1:2025 Clause 5 prequalified joint details qualify without a PQR test. The WPS must document the process, filler metal classification, preheat per Table 5.11, and position qualification.
Do welder qualifications apply to cable tray support welding?
Yes. Every welder working to a D1.1 WPS must hold a current WPQ covering the process, position, and base metal thickness range being welded. Welder continuity under Clause 6.4.1 (the six-month rule) also applies—track your welder roster regardless of job type.