Sub-fabrication is a normal part of structural steel production. A prime fabricator bids the whole project, then sends plate girder components to a shop with a larger press brake, HSS column sections to a shop with a certified tube welding program, or deck attachment hardware to a smaller vendor with available capacity. The commercial arrangement is familiar. The quality responsibility is less clearly understood.
The critical point: under AWS D1.1:2025, the entity doing the welding is the contractor responsible for qualification, inspection, and documentation — regardless of whether that entity is the prime or a sub-tier. A sub-fabricator cannot outsource its quality obligations to the prime by virtue of being downstream in the supply chain.
AWS D1.1:2025 and the Concept of "The Contractor"
AWS D1.1:2025 uses the term "Contractor" throughout to mean the party performing the welding work and responsible for compliance with the code requirements. The Contractor is responsible for:
- Qualifying welding procedures (WPS) or using prequalified procedures
- Qualifying welders for the processes, positions, and base metals required
- Maintaining a quality control system including inspection
- Retaining documentation (PQR records, WPQ records, inspection reports)
When you are a sub-fabricator, you are "the Contractor" for your scope. The prime contractor does not inherit your obligations simply by being the party of contract with the owner. You own your quality system for the work you perform.
WPS Ownership: Which Procedures Can a Sub-Fab Use?
A sub-fabricator has three procedural paths:
1. Its Own Qualified WPS
The cleanest arrangement. The sub-fab's quality system maintains its own WPS documents, supported by its own PQR records or prequalified procedures under Clause 5. Its welders are qualified to those procedures. Its CWI inspects the work and signs off inspection records in the sub-fab's name.
This is the right answer for any sub-fabricator doing significant volume of a particular joint type. If you're making fifty plate girder splices per year, you should have your own WPS for that splice joint — not borrowing a procedure every time.
2. Prime Contractor's WPS, Formally Adopted
If the prime contractor has qualified procedures that cover the sub-fab's scope, the sub-fab can formally adopt those procedures — but adoption has specific requirements:
- The sub-fab's quality system must reference and control the adopted procedure (a copy on file, revision-controlled)
- The sub-fab's welders must be individually qualified to the procedure's essential variable requirements
- The sub-fab's responsible QC authority must acknowledge in writing that the procedure is being used under its quality system
- Any essential variable restrictions in the procedure apply equally to the sub-fab's work (position limits, base metal groups, thickness ranges, interpass temperature limits)
What the sub-fab cannot do is assume that because a prime's WPS exists, the sub-fab's welders are automatically qualified, or that the prime's welder certifications extend to sub-fab employees.
3. Prequalified WPS
If the sub-fab's work falls within the scope of prequalified procedures under AWS D1.1:2025 Clause 5 — Table 5.6 base metals, low-hydrogen fillers, standard joint geometries from Clause 5 Figures 5.1 through 5.3 — no PQR is required, and the sub-fab can write its own prequalified WPS without referencing the prime's procedures at all. This is often the most practical path for sub-fabs doing routine structural work.
Rule library based on AWS D1.1:2025; verify against your governing edition.
Welder Qualification: Sub-Fab's Own Responsibility
Welder qualification records (WPQs) are personal to the individual welder and are owned by the entity that performed the qualification test. If the prime contractor tested and qualified a welder, that qualification record belongs to the prime — not to the sub-fab employer.
Sub-fab welders must be qualified for the processes, base metal groups, positions, and thickness ranges required by the work. The sub-fab cannot rely on the prime's welder qualifications for its own employees. If the sub-fab acquired those welders from the prime as part of a business arrangement, it must obtain copies of the original WPQ records and verify that continuity has not lapsed.
The six-month continuity requirement under AWS D1.1:2025 Clause 6.4.1 applies equally to sub-fab welders. If a welder has not performed the qualified process in the preceding six months, requalification is required regardless of who originally issued the qualification.