6 min read

Mezzanine Platform Structural Welding: WPS Requirements Under AWS D1.1

Practical WPS guide for fab shops welding mezzanine and elevated platform steel: code applicability, base metal coverage, fillet weld sizing, and CWI inspection requirements per AWS D1.1:2025.

New to procedures? Start with WPS welding: what a welding procedure specification is, with a filled-in example.

Mezzanine and elevated platform structures are a staple of the structural fab shop's production floor: storage platforms, work platforms, equipment support mezzanines, and in-plant elevated floors are routinely fabricated and erected. Despite their apparent simplicity compared to a moment frame or transfer structure, mezzanines require the same WPS documentation, welder qualifications, and CWI inspection that any AWS D1.1 structural weld job demands. This gap in documentation is a frequent finding in AISC certification audits for shops that treat mezzanines as "miscellaneous" work outside their quality program.

Code Applicability to Mezzanine Structures

AWS D1.1 applies to welded structural steel in buildings and structures, and mezzanines are explicitly within the IBC's definition of a structure. When a project has IBC Chapter 17 special inspection requirements, structural steel welding on the mezzanine will be listed in the special inspection schedule, triggering D1.1 inspection.

Even without special inspection, an AISC-certified fabricator's quality program must cover all structural steel in its scope. If the shop fabricates the mezzanine columns, beams, and base plates, it needs a qualifying WPS for every weld type made—column-to-base plate fillet welds, beam web-to-column shear tab welds, bracing connection fillet welds, and any groove welds at moment or splice connections.

One common misconception: "It's a simple fillet weld mezzanine, no special inspection, no seismic—D1.1 doesn't really apply." This conflates inspection frequency with code applicability. D1.1 sets the construction standard. The shop's quality program references D1.1 for WPS development and workmanship requirements regardless of whether a special inspector is on-site every shift.

Base Metals Commonly Used in Mezzanine Construction

Mezzanine framing typically uses three base metals, all of which are prequalified in AWS D1.1:2025 Table 5.6:

ASTM A36 (Fy = 36 ksi) — the most common material for angles, plates, channel, and low-load beams and columns. Table 5.6, Group I. Prequalified for use with low-hydrogen filler metals in SMAW, FCAW-G, GMAW, and SAW processes.

ASTM A992 (Fy = 50 ksi, Fu = 65 ksi) — the standard wide-flange column and beam material. A992 is designated as a Group II material in Table 5.6. It pairs well with E7018 or E71T-1 filler metals and is prequalified under Clause 5.

ASTM A500 Grade B/C (Fy = 46/50 ksi) — HSS tube columns and bracing. Table 5.6, Group II. When HSS is used as mezzanine columns, the WPS must address the tube wall thickness range and confirm prequalification conditions are met for fillet welds at base plates and gusset connections.

Dissimilar base metal joints — a mezzanine often connects A992 wide-flange beams to A500 HSS columns, or A36 gusset plates to A992 framing. These are addressed in D1.1:2025 Clause 5.6 and the prequalified filler metal selection rules: use a filler metal that matches or slightly overmatches the lower-strength base metal's tensile requirements. E7018 (minimum 70 ksi tensile) is appropriate for A36/A500/A992 joints.

Typical Mezzanine Connections and WPS Coverage

A well-organized mezzanine WPS library covers these connection types:

Column Base Plate Welds

The most critical mezzanine weld is the column base plate: typically a T-joint fillet weld around the column perimeter, sometimes supplemented with PJP groove welds for moment-resisting base connections. Fillet weld size is set by the structural engineer; the WPS must cover the specified fillet size within the qualified range.

For a typical W6×15 or HSS 6×6×1/4 column to a 3/4-inch A36 base plate:

  • Thinner part (T) = 3/4-inch base plate
  • Table 7.7 minimum fillet = 1/4 inch (for T in the 1/2 in to 3/4 in range)
  • Structural engineer typically specifies 5/16-inch or 3/8-inch fillet at anchor-rod constrained base plates

Rule library based on AWS D1.1:2025; verify against your governing edition.

Beam-to-Column Shear Tab Connections

Shear tabs are the most common mezzanine beam connection: a 3/8-inch or 1/2-inch plate shop welded to the column flange or web with fillet welds, then field-bolted to the beam web. The shop WPS covers the tab-to-column fillet welds; the field bolts are beyond welding scope.

This joint is entirely prequalifiable under Clause 5 for A36 tab to A992 column using SMAW E7018 or FCAW-G E71T-1.

Bracing Gusset Connections

Mezzanine bracing angles or hollow sections connect to frames through gusset plates with fillet welds. The gusset-to-frame joint is a T-joint or corner joint, fully prequalifiable. Confirm the connection geometry against Clause 5 joint detail figures to ensure it meets prequalification geometry limits.

Stair Stringer and Guardrail Attachments

Stairs and guardrails on mezzanines are often fabricated in the same shop as the main framing. The stringer and post connections typically require their own WPS if they are welded structural connections rather than bolted only. The same prequalified WPS used for the mezzanine framing can often cover these attachments if the base metal, filler metal, and joint geometry are within range.

WPS Documentation for Mezzanine Work

The WPS must comply with AWS D1.1:2025 Annex J Form J-1 format requirements. For a comprehensive mezzanine WPS, document:

  • Process: SMAW, FCAW-G, or GMAW (or combinations if multi-process)
  • Joint type(s): Fillet, PJP groove (if moment base or continuity plates), CJP groove (if full-penetration beam splices)
  • Base metal: Specification (ASTM A36, A992, A500) and thickness range covered
  • Filler metal: AWS specification number, classification, and trade name (optional but useful for traceability)
  • Preheat / interpass temp: Per Table 5.11 for the base metal and thickness combination. A36 and A992 at standard mezzanine member thicknesses (up to 3/4-inch) typically require no preheat above 32°F [0°C] with low-hydrogen processes
  • Position(s): 1F, 2F for typical shop work; include 3F and 4F if field welds are anticipated in vertical or overhead positions
  • Qualification basis: "Prequalified per AWS D1.1:2025 Clause 5" with supporting clause references

The WPS number and revision should appear on all weld maps and traveler documents to maintain traceability from the production record back to the qualifying document.

CWI Inspection Protocol for Mezzanine Structural Welds

Pre-Weld Checks

Before the arc strikes:

  • Verify base metal identification (CMTRs on file for all primary members)
  • Confirm fit-up gap meets Clause 5 or WPS limits (fillet weld maximum gap 3/16 inch per D1.1)
  • Check filler metal classification matches WPS; confirm electrodes from sealed container or heated oven
  • Verify welder WPQ is current for the process, position, and thickness being welded
  • Apply preheat if the material temperature or ambient conditions require it per Table 5.11

In-Process

Monitor interpass temperature, pass sequence (documented in WPS for multi-pass joints), and slag removal between passes. For base plate welds, watch for underfill at starts and stops—common at corners where the welder changes direction.

Post-Weld Visual

Using a bridge cam or fillet weld gauge, verify:

  • Fillet weld size equals or exceeds the specified size
  • Leg dimensions acceptable (no convexity or concavity beyond allowable limits per Clause 7.9)
  • Underfill at craters within tolerance or repaired
  • No visible cracks, porosity clusters, or overlap
  • Arc strikes outside the weld zone repaired

For NDE beyond visual, the special inspection schedule or owner specification governs. MT spot inspection on column base plate welds is sometimes required for seismic design categories C, D, E, and F per IBC Chapter 17 and AWS D1.8.

WPS Library Organization for Mezzanine Scope

A clean approach for shops that regularly fabricate mezzanines is a consolidated "Miscellaneous Structural / Light Manufacturing" WPS that covers A36, A992, A500 in all fillet weld positions with SMAW E7018 and FCAW-G E71T-1. This single prequalified WPS document, covering a reasonable thickness range (say, 3/16 inch to 1-1/2 inch for the thinner part) in all flat, horizontal, vertical, and overhead positions, can serve the entire mezzanine product line.

Pair it with a scope statement in your QC manual that explicitly lists mezzanines, elevated platforms, and work platforms under the shop's fabrication scope, and the AISC certification auditor has a clear trail from scope to WPS to production record.

For related content, see our guide on prequalified WPS under Clause 5 and the CWI pre-weld inspection checklist before arc. For WPS document generation, our pricing page shows how the WPSwelding platform generates compliant Annex J form WPS documents in minutes.

For structural fabricators building out a full WPS library to cover their product range—including mezzanines, support steel, and specialty connections—see welding procedure library audit ready for the complete AISC audit prep checklist.

FAQ

Frequently asked.

Does AWS D1.1 apply to mezzanine and elevated platform structures?
Yes. Mezzanine structures made from welded structural steel—beams, columns, columns bases, bracing, and connections—fall within the AWS D1.1 scope when the project specifications call it out. IBC Chapter 17 special inspection typically applies to mezzanines in occupancies requiring special inspections, triggering D1.1 inspection requirements. Confirm the governing code with the EOR and special inspection agency.
What WPS qualification route is typical for mezzanine beam-to-column connections?
Most mezzanine connections use prequalified WPS under AWS D1.1:2025 Clause 5. A36, A992, and A500 base metals are all listed in Table 5.6, allowing fillet and CJP groove welds without a PQR test when all Clause 5 conditions are met. If the connection geometry deviates from prequalified joint details, a tested WPS per Clause 6 is required.
What is the minimum fillet weld size for mezzanine column base plate welds?
Per AWS D1.1:2025 Table 7.7, minimum fillet weld size is based on the thinner part thickness (T) for low-hydrogen processes. A 3/4-inch base plate connected to a column requires a minimum 1/4-inch fillet weld. The structural engineer typically specifies a larger design weld size; the Table 7.7 minimum is a code floor, not the design weld.
What NDE is required on mezzanine structural welds?
Visual inspection is required for all structural welds. Additional NDE (UT, MT, or RT) on mezzanine connections is not required by D1.1 by default—it is project-specific based on the special inspection schedule, owner spec, or seismic design category. Demand-critical welds in higher seismic design categories require NDE per AWS D1.8 supplemental provisions.

More from the blog