ASTM A500 Grade C HSS: CVN Toughness and WPS Qualification
ASTM A500 Grade C has no mandatory Charpy impact requirement. For seismic SDC D/E/F and demand-critical applications, understand what this gap means for your WPS qualification program.
ASTM A500 Grade C is the most common specification for cold-formed hollow structural sections (HSS) in structural steel construction. It covers rectangular, square, and round HSS with minimum yield strengths of 50 ksi (rectangular and square) and 50 ksi (round), and minimum ultimate tensile strengths of 62 ksi and 58 ksi respectively. It is in AWS D1.1:2025 Table 5.6 as a prequalified base metal — straightforward, widely available, and covered by standard WPS qualification programs.
But A500 Grade C has a toughness gap that creates complications in certain applications, and understanding that gap is part of running a sound WPS qualification program for shops that work on seismic or owner-specified toughness projects.
The Charpy Gap in ASTM A500
ASTM A500 itself does not include a mandatory Charpy V-notch (CVN) requirement. The standard specifies yield and tensile strength minimums, elongation, and dimensional tolerances — but no requirement that the material withstand a specified impact energy at a specified test temperature.
This is in contrast to, for example, ASTM A913 Grade 65 (a quenched and self-tempered steel used for heavy columns), which includes a 40 ft-lb CVN requirement at 70°F. Or ASTM A1085, the newer HSS specification that was developed specifically to address A500's shortcomings, including a mandatory 25 ft-lb requirement at 40°F as a mill-certifiable property.
For a CWI or QC manager, the practical significance is this: if your project specification or the applicable code requires the base metal to demonstrate a minimum notch toughness, A500 Grade C may not satisfy that requirement without supplementary testing or a mill cert that includes optional CVN data.
AWS D1.1 Table 6.8 and When It Activates
AWS D1.1:2025 Table 6.8 lists the supplementary essential variables for CVN Charpy impact testing. These variables control aspects of the WPS that affect weld metal toughness: the classification of the filler metal (specifically whether it has a notch-toughness designator), heat input limits, and certain electrode type restrictions. The critical point is that Table 6.8 variables are only triggered when the contract documents or the applicable code require CVN testing of the weld metal.
For routine non-seismic structural work — office buildings, industrial platforms, equipment supports — the contract documents typically do not invoke CVN testing requirements. Table 6.6 essential variables apply, and there is no supplementary variable set in play. Under those conditions, A500 Grade C is straightforward: it is prequalified, it is compatible with common filler metals (ER70S-6 for GMAW, E71T-1 for FCAW-G, E7018 for SMAW), and the WPS qualification proceeds normally.
The trigger for Table 6.8 is project-specific. When you see any of the following, check with the EOR or specification:
AISC 341 (Seismic Provisions for Structural Steel Buildings) governs
AWS D1.8 (Seismic Supplement) is referenced
The special inspection program lists "demand-critical welds"
The specification explicitly calls for CVN qualification of the WPS
When those triggers are present, the WPS program must include PQR testing with CVN specimens, and the essential variable set expands to include Table 6.8 items.
Demand-Critical Welds and A500 Grade C HSS
AWS D1.8 applies to seismic force-resisting systems (SFRS) in Seismic Design Categories D, E, and F. Within that standard, demand-critical welds are defined as connections where fracture would be catastrophic to the structural system — typically the welds at beam-to-column connections in moment frames, and welds at brace-to-gusset-plate connections in special braced frames.
For demand-critical welds, AWS D1.8 specifies that:
The filler metal must have a minimum CVN classification (40 ft-lb at –20°F or similar, depending on exposure category)
The WPS must be qualified with CVN testing of the weld metal (supplementary essential variables apply)
The base metal must meet specific notch toughness requirements if the connection type requires it
This is where A500 Grade C HSS — frequently used for HSS columns, bracing members, and chord members — creates a question. ASTM A500 Grade C does not have a mill-certifiable CVN requirement. If the project specification requires the base metal to have a documented CVN value (not just a nominal ASTM A500 cert), the mill will typically not be able to provide this from standard production. Supplementary mill testing can sometimes be ordered, but it is not part of the standard ASTM A500 scope.
AISC 341 addresses this through its material requirements section, which specifies that HSS members in certain SFRS applications should use material with an adequate toughness requirement. Many engineers and projects now specify ASTM A1085 HSS for seismic applications precisely because A1085 includes a mandatory CVN requirement (25 ft-lb at 40°F) and improved dimensional tolerances.
WPS Implications for Shops Working on Seismic Projects
If your shop fabricates HSS connections for seismic SFRS applications, the WPS qualification program must address the following:
Filler metal selection with notch-toughness classification. For demand-critical welds, the filler metal must carry a notch-toughness designator appropriate for the specified exposure temperature. For FCAW-G, this means using an electrode classified under AWS A5.20 or A5.36 with an appropriate impact test designator rather than a plain E71T-1C. For SMAW, E7018-1 (which carries a CVN requirement) rather than plain E7018 may be specified. The WPS must document this explicitly.
PQR with CVN test specimens. When Table 6.8 applies, the PQR coupon must yield CVN specimens, and those specimens must be tested to demonstrate the minimum energy at the specified temperature. The test results are reported on the PQR, and they define the heat input range within which the qualified weld metal toughness remains valid.
Heat input limits in the WPS. One of the Table 6.8 essential variables is a maximum heat input limit. High heat input welds produce a coarser grain heat-affected zone (HAZ) and can reduce impact toughness below the qualified level. If the WPS was qualified at a moderate heat input range and production welding runs at higher heat input (faster travel speed reduction, higher amperage), toughness results from production welds may not reflect PQR results. For shops doing seismic HSS work, production parameter logging becomes important — not just for code compliance documentation, but as a toughness quality control.
Preheat on A500 Grade C. AWS D1.1:2025 Table 5.11 gives minimum preheat requirements by base metal category and thickness. A500 Grade C, being a cold-formed carbon steel, falls under the applicable steel group in that table. For thicker HSS (walls over 3/4 inch) with moderate or high restraint, preheat to Table 5.11 minimums is required regardless of seismic demand — it is the standard non-seismic requirement. For seismic SFRS work, AWS D1.8 may specify additional or more restrictive preheat requirements.
A1085 as the Preferred Alternative for Seismic HSS
ASTM A1085 was published specifically to address the gaps in ASTM A500 for structurally demanding applications. Key improvements over A500 Grade C:
Mandatory CVN requirement: 25 ft-lb minimum at 40°F, mill-certifiable
Single yield strength grade: 50 ksi minimum (no Grade A/B/C confusion)
Tighter dimensional tolerances: less wall thickness variation than A500
Smaller yield-to-tensile ratio range: better performance predictability in seismic design
For shops where the EOR specifies A1085, the WPS qualification program changes only slightly: A1085 is in AWS D1.1:2025 Table 5.6 as a prequalified base metal, and it is compatible with the same filler metals used for A500 Grade C. If you have an existing WPS qualified on A500 Grade C, check whether A1085 falls within the base metal group coverage of that procedure, or whether a separate WPS is needed.
For non-seismic work, A500 Grade C remains the standard specification and raises no WPS complications. The toughness question only becomes material when the project specification — either directly or by reference to AISC 341 or AWS D1.8 — requires documented notch toughness in the base metal or weld metal.
Practical Documentation Guidance
When reviewing mill certifications for A500 Grade C on a seismic project, verify that:
The cert is for Grade C (not Grade A or B, which have lower yield and sometimes different toughness characteristics)
If the EOR requires supplemental CVN documentation, it appears on the cert — standard A500 certs will not include this
The heat number is traceable to the structural members as required by your material traceability program
When documenting the WPS program, clearly note which procedures are intended for seismic demand-critical welds and which are for non-demand-critical connections. The two programs may use different filler metal classifications, different essential variable sets (Table 6.6 vs. Table 6.6 plus Table 6.8), and different parameter logging requirements.
Rule library based on AWS D1.1:2025; verify against your governing edition — the AHJ or contract may specify 2020 or earlier.
FAQ
Frequently asked.
Does ASTM A500 Grade C meet the base metal toughness requirements for AWS D1.8 demand-critical welds?
Not automatically. ASTM A500 Grade C does not include a mandatory Charpy V-notch requirement. AWS D1.8 and AISC 341 impose supplementary base metal toughness requirements for demand-critical welds in high-seismic applications. If your project requires this, verify with the EOR whether supplementary testing or a material substitution is required.
Does AWS D1.1:2025 require CVN testing for WPS qualification on A500 Grade C HSS?
Not by default. AWS D1.1 supplementary essential variables in Table 6.8 are triggered only when the contract documents or applicable code (such as AISC 341 or AWS D1.8) require notch toughness testing. For routine non-seismic structural work, standard Table 6.6 essential variables apply without CVN.
Is A500 Grade C a prequalified base metal under AWS D1.1:2025?
Yes. ASTM A500 is listed in Table 5.6 of AWS D1.1:2025 as a prequalified base metal, allowing its use in prequalified WPS applications. However, being prequalified for WPS purposes does not eliminate any seismic-related supplementary testing your project specification may require.
Can I substitute A500 Grade C with A1085 to close the toughness gap?
ASTM A1085 HSS includes a mandatory minimum Charpy impact requirement (25 ft-lb at 40°F), which addresses the toughness gap. A1085 is also listed in Table 5.6 and is compatible with the same filler metals used for A500. Many engineers spec A1085 for seismic HSS members specifically because of this requirement.